|
1 1/2 Inch Brace Bracket
Product Code:
PLD014
The Brace Bracket should be used on installations where there is deep water, or if a boat is often moored at the dock, to eliminate side motion.
|
|
1 1/2 Inch Clamp on Brace Bracket
Product Code:
PLD012
Used in the same manner as our Brace Bracket but clamps over the outside of the pipe for easier installation.
|
|
1 1/2 Inch Pipe Base
Product Code:
PLD005
The Pipe Base should be used where the Lake bottom is soft or muddy. The base will eliminate a lot of the side to side motion in the dock. Extend pipe about 1 1/2 feet through the center hole and lock the set bolt. Using a Drive Cap, hammer in until bas
|
|
1 1/2 Inch Pipe Corner Bracket
Product Code:
PLD003
The Pipe Side and Corner Brackets are used with 1 1/2" ID galvanized pipe legs. Use one set on each end of dock and one set to connect each dock section together with two or four 3/8" bolts, washers and nuts. When installing a "T" or "L" shaped dock, use
|
|
1 1/2 Inch Pipe Point
Product Code:
PLD010
The Pipe Point can be used in any situation, but is very helpful where the Lake bottom is extra firm. It also eliminates sand getting inside the pipe when driven into the Lake bottom. Attaches to end of pipe with 2 3/8 inch set screws. Seat point about ha***
|
|
1 1/2 Inch Pipe Side Bracket
Product Code:
PLD001
The Pipe Side and Corner Brackets are used with 1 1/2" ID galvanized pipe legs. Use one set on each end of dock and one set to connect each dock section together with two or four 3/8" bolts, washers and nuts. When installing a "T" or "L" shaped dock, use
|
|
1 1/2 Inch Pipe Trim Cap
Product Code:
PLD007
The Pipe Trim Cap is used for protection from sharp edges on the pipe as well as adding a more professional look to your dock.
|
|
2 Inch Brace Bracket
Product Code:
PLD015
The Brace Bracket should be used on installations where there is deep water, or if a boat is often moored at the dock, to eliminate side motion. Picture shown is 1 1/2.
|
|
|
2 Inch Clamp on Brace Bracket
Product Code:
PLD013
Used in the same manner as our Brace Bracket but clamps over the outside of the pipe for easier installation. Picture shown is 1 1/2.
|
|
2 Inch Pipe Base
Product Code:
PLD006
The Pipe Base should be used where the Lake bottom is soft or muddy. The base will eliminate a lot of the side to side motion in the dock. Extend pipe about 1 1/2 feet through the center hole and lock the set bolt. Using a Drive Cap, hammer in until bas
|
|
|
2 Inch Pipe Corner Bracket
Product Code:
PLD004
The Pipe Side and Corner Brackets are used with 2" ID galvanized pipe legs. Use one set on each end of dock and one set to connect each dock section together with two or four 3/8" bolts, washers and nuts. When installing a "T" or "L" shaped dock, use the
|
|
2 Inch Pipe Point
Product Code:
PLD011
The Pipe Point can be used in any situation, but is very helpful where the Lake bottom is extra firm. It also eliminates sand getting inside the pipe when driven into the Lake bottom. Attaches to end of pipe with 2 3/8 inch set screws. Seat point about ha
|
|
|
2 Inch Pipe Side Bracket
Product Code:
PLD002
The Pipe Side and Corner Brackets are used with 2" ID galvanized pipe legs. Use one set on each end of dock and one set to connect each dock section together with two or four 3/8" bolts, washers and nuts. When installing a "T" or "L" shaped dock, use the
|
|
2 Inch Pipe Trim Cap
Product Code:
PLD008
The Pipe Trim Cap is used for protection from sharp edges on the pipe as well as adding a more professional look to your dock. Picture shown is 1 1/2.
|
|
Brace Clamp
Product Code:
PLWLD016
For an extra rigid dock, use two 1/2 inch Brace Pipes in a cross pattern and our Brace Clamp attached to the center of the cross. The Brace Clamp attaches easily with two bolts.
|
|
Combination 1 1/2 or 2 Inch Drive Caps
Product Code:
PLD009
The Combination Drive Cap is used when driving the pipe legs into the lake bottom to help prevent flaring damage to the pipe. Tie a small piece of rope to the Drive Cap and secure the other end to the dock.
|
|
Schedule 40 Galvanized Pipe (I.D. 1 1/2 Inch O.D. 1 7/8 Inch)
Product Code:
GP018
Use for dock legs and bracing. All pipe cut to order up to nine feet in length shipping via UPS. All pipe F.O.B. Franklin, NH. If you need your pipe specifically cut, or have other special requirements, please email us.***
|
|
Schedule 40 Galvanized Pipe (I.D. 1/2 Inch O.D. 3/4 Inch)
Product Code:
GP017
Use for dock legs and bracing. All pipe cut to order up to nine feet in length shipping via UPS. All pipe F.O.B. Franklin, NH. If you need your pipe specifically cut, or have other special requirements, please email us.***
|
|
|
Schedule 40 Galvanized Pipe (I.D. 2 Inch O.D. 2 3/8 Inch)
Product Code:
GP019
Use for dock legs and bracing. All pipe cut to order up to nine feet in length shipping via UPS. All pipe F.O.B. Franklin, NH. If you need your pipe specifically cut, or have other special requirements, please email us.***
|
|
|
